Bellamy & Co. LLC Chris Hempfling Music Equipment Online Auction (#150579) 04/03/2018 8:00 AM CST - 04/25/2018 3:30 PM CST CLOSED! Auction info Bellamy & Co. LLC View Advanced Search ▼ Items per page 102550100 Advanced Search Sort by DefaultTime LeftLot#Lot NameNewestHighest PriceLowest PriceBidsViewsTaxes Filter By Categories Category match ANY of the aboveALL of the above Featured Exclude closed lots Price Auctioneer Lot Number Results: Viewing items 1-36 of 36. Previous|1|Next Lot #100 2014 Covered Wagon 7x14 Enclosed Trailer- Well maintained one owner trailer. Dual Axle with electric brakes Wood Floor 3500lb axles Great Tires View details Winning BidN/A Lot #101 Fender Blues Deluxe Reissue Tube Amp- 40 watt Eminence Speaker 2 Channel 3x12AX7 and 2 6L6 Tubes complements. Solid state rectifier Effects loop Fender Spring reverb View details Winning BidN/A Lot #102 OSP Elite Core 8 Channel Snake (25ft)- Elite Core snakes feature 24 gauge shielded lines with foil shield and a drain wire on each channel. All channels and returns are fully balanced and shielded, with XLR connectors throughout. Each Elite Core stage snake also comes with a bag to cover the stage box or fan during transport or storage. 8 Balanced XLR Channels 4 Balanced XLR Returns Shielded Twisted Pair with foil and drain wire Low Oxygen Copper Metal Strain Relief on both fanout and box end Neoprene jacket Each channel labeled Easy pull handle on stage box Heavy-duty heat shrink over the entire length of fanout Cable management disk on fanout Field-serviceability with machine screws to attach connectors to box View details Winning BidN/A Lot #103 QSC PL 325 Power Amp- STEREO MODE, Both Channels Driven: - 8 ohms EIA 1 kHz 1% THD: 500 W - 4 ohms EIA 1 kHz 1% THD: 850 W - 2 ohms EIA 1 kHz 1% THD: 1250 W BRIDGE MONO MODE: - 8 ohms EIA 1 kHz 1% THD: 1700 W - 4 ohms EIA 1 kHz 1% THD: 2500 W - Maximum Distortion (20 Hz - 20 kHz, 1 dB below rated power) 4 to 8 ohms: 0.05% - Frequency Response (8 ohms): 20 Hz - 20 kHz, +/-0.2 dB - Noise (20 Hz - 20 kHz, 32 dB Gain): -106 dB - Dynamic Headroom (4 ohms): 2 dB - Damping Factor (8 ohms): 500 - Output Circuitry: Class H (2-tier) - Input Gain (1.2V setting): 34.5 dB - Input Impedance: > 10k ohms balanced, or unbalanced - Cooling:: Variable-speed fan, rear-to-front air flow - Connectors (each channel): Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel). Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts. DataPort: HD-15, input signal in parallel with XLR input connectors - Front Controls: AC Power Switch, Gain Controls, 21 detents, 1 dB steps (each channel) - Front indicators (LED color): Power (Blue), Bridged (Yellow), Parallel (Orange), Clip/Prot (Red x 2), Level -10 (Orange x 2), Level -20 (Green x 2), Signal -35 (Green x 2), - Rear Controls (with LED indicators): Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange), Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow), High Pass (each channel): 3 Hz (Off), 30 Hz (Yellow), or 50 Hz (Orange), Clip Limiter (each channel): Off, On (Yellow) - Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection. On/off muting, DC fault shutdown, active inrush limiting - Dimensions: (H x W x D) 3.5 x 19 x 15.6" (8.9 x 48.3 x 15.63 cm) - Weight: 22 lbs (10 kg) Weight, Dimensions, and Manufacturer Part Numbers Shipping Weight: 32 lbs Shipping Dimensions: 24 x 22 x 7 in View details Winning BidN/A Lot #104 QSC PL 325 Power Amp- STEREO MODE, Both Channels Driven: - 8 ohms EIA 1 kHz 1% THD: 500 W - 4 ohms EIA 1 kHz 1% THD: 850 W - 2 ohms EIA 1 kHz 1% THD: 1250 W BRIDGE MONO MODE: - 8 ohms EIA 1 kHz 1% THD: 1700 W - 4 ohms EIA 1 kHz 1% THD: 2500 W - Maximum Distortion (20 Hz - 20 kHz, 1 dB below rated power) 4 to 8 ohms: 0.05% - Frequency Response (8 ohms): 20 Hz - 20 kHz, +/-0.2 dB - Noise (20 Hz - 20 kHz, 32 dB Gain): -106 dB - Dynamic Headroom (4 ohms): 2 dB - Damping Factor (8 ohms): 500 - Output Circuitry: Class H (2-tier) - Input Gain (1.2V setting): 34.5 dB - Input Impedance: > 10k ohms balanced, or unbalanced - Cooling:: Variable-speed fan, rear-to-front air flow - Connectors (each channel): Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel). Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts. DataPort: HD-15, input signal in parallel with XLR input connectors - Front Controls: AC Power Switch, Gain Controls, 21 detents, 1 dB steps (each channel) - Front indicators (LED color): Power (Blue), Bridged (Yellow), Parallel (Orange), Clip/Prot (Red x 2), Level -10 (Orange x 2), Level -20 (Green x 2), Signal -35 (Green x 2), - Rear Controls (with LED indicators): Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange), Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow), High Pass (each channel): 3 Hz (Off), 30 Hz (Yellow), or 50 Hz (Orange), Clip Limiter (each channel): Off, On (Yellow) - Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection. On/off muting, DC fault shutdown, active inrush limiting - Dimensions: (H x W x D) 3.5 x 19 x 15.6" (8.9 x 48.3 x 15.63 cm) - Weight: 22 lbs (10 kg) Weight, Dimensions, and Manufacturer Part Numbers Shipping Weight: 32 lbs Shipping Dimensions: 24 x 22 x 7 in View details Winning BidN/A Lot #105 EV TX1152 Speaker Cabinet- High-output, high-quality sound Excellent pattern control for medium throw use Low-distortion SMX2151 woofer with fully symmetric drive 1.25-inch DH3/2010A titanium HF compression driver Rotatable Constant-directivity 60º x 40º horn Advanced 4th-order crossover with HF protection 100 dB sensitivity, 133 dB maximum SPL Power handling: 500 W continuous, 2000 W peak Lightweight trapezoidal plywood/MDF enclosure Pole mount for use with subwoofer or stand Six 3/8-inch threaded suspension points Black EVCoat™ finish View details Winning BidN/A Lot #106 EV TX1152 Speaker Cabinet- High-output, high-quality sound Excellent pattern control for medium throw use Low-distortion SMX2151 woofer with fully symmetric drive 1.25-inch DH3/2010A titanium HF compression driver Rotatable Constant-directivity 60º x 40º horn Advanced 4th-order crossover with HF protection 100 dB sensitivity, 133 dB maximum SPL Power handling: 500 W continuous, 2000 W peak Lightweight trapezoidal plywood/MDF enclosure Pole mount for use with subwoofer or stand Six 3/8-inch threaded suspension points Black EVCoat™ finish View details Winning BidN/A Lot #107 Rolling Road Case (with assorted speaker cable)- Assorted length speakon style cables in a large rolling case. View details Winning BidN/A Lot #108 Peavey FX2 24 Mixer (in road case)- High-power dual DSP engine with improved digital effects and output processing including Feedback Ferret®, 28-band GEQ/5-band PEQ, delay and limiter USB 2.0 "A" connection to record directly to or playback from memory stick USB 2.0 "B" connection for streaming digital out 3-band EQ with sweepable mid-frequency and variable low cut filters 2 stereo channels with dual mic/line inputs 48 volt phantom power 4 subgroups 100mm faders Double the processing power of the orginal FX Series All new switching power supply design is more efficient than the original Silencer™ mic preamp XLR inputs USB 2.0 Streaming Compatibility: Windows XP/Vista/7/8/8.1/10 ; Mac OSX playback only 6 Aux sends Weight Packed: 35.00 lb(15.876 kg) Width Packed: 25"(63.5 cm) Height Packed: 28"(71.12 cm) Depth Packed: 11.5"(29.21 cm) View details Winning BidN/A Lot #109 Carvin SNK24XR 24 Channel Snake (Spool Real 100ft)- All channels and returns are fully balanced and shielded, with XLR connectors throughout. Snake comes mounted to easy to use spool 24 Balanced XLR Channels 4 Balanced XLR - 1/4" Returns Shielded Twisted Pair with foil and drain wire Low Oxygen Copper Metal Strain Relief on both fanout and box end Neoprene jacket Each channel labeled View details Winning BidN/A Lot #110 Rapco 24 Channel Snake (100')- 24 Balanced XLR Channels 4 Balanced XLR Returns View details Winning BidN/A Lot #111 Allen & Heath GL2400 32 Channel Mixer (with road case)- 32 channel LR and M main outputs 4 Audio groups with pan control 6 Auxiliary sends with per-channel pre/post fader switching 2 stereo channels, each with mic and dual stereo line inputs 7×4 Matrix Proper dual functionality for FoH and/or Monitor mixing M can be configured as LR sum, Wedge, or Aux-Fed Sub or C master Recording capable with channel direct outputs Matrix external inputs with level trims and common input capability Stereo channel line inputs can be independently routed to LR Stereo channel mic input breakpoints for cross patching into matrix Responsive 4 band, 2 sweep EQ 100Hz channel high pass filters Individual phantom power and polarity switching Dedicated channel, master and stereo monitor meters Internal jumper plugs for pre/post-EQ aux, direct out and other options Mutes, meters and AFL on all fader masters Assignable talkback 1kHz oscillator and pink noise generator 2-track monitoring and replay to LR Headphones and local monitor outputs Electronically balanced XLR outputs with +26dBu drive capability Preamp 74dB range with +34dBu input capability for mic or line Ultra low noise mix head amp design Internal power supply with socket for MPS12 backup supply (16ch to 32ch models) External RPS11 power supply and socket for backup supply (40ch model only) 100mm dust protected faders Metal jacks, gold-plated XLRs, sealed pots and switches Individual circuit card assembly with nutted pots Sys-Link V2 console input/output linking option 4-pin XLR lamp sockets View details Winning BidN/A Lot #112 JBL JRX112M Monitor- JBL 12 in low frequency driver with a 64 mm (2.5 in) diameter edgewound ribbon voice coil which provides more cross-sectional wire area in the voice coil gap than round wire designs, for greater efficiency and power handling. Ferro-fluid cooled compression driver with titanium diaphragm improves high frequency performance as well as system reliability. The advanced network topology crossover design shapes frequency response and delivers "coherent summation" in the crossover region. High-voltage capacitors and inductors with massive cores and heavy gauge wire enable the crossover network to handle high power without saturating. Progressive Transition™ high frequency waveguide provides superior coverage control, reduced distortion, and smoother frequency response. The rugged, acoustically superior enclosure is constructed from 19 mm (.75 in) MDF (Medium Density Fiberboard) using advanced adhesives and mechanical fastener technology for extreme durability and improved low-frequency performance. SonicGuard™ protects the highfrequency driver from excess power without interrupting the performance. Non-resonant, all-steel handles are used. Attractive 18-gauge hexagon perforated, steel grille protects components from damage. Dual-angle pole-mount socket allows the speaker to tilt 10°for more uniform audience coverage. SPECIFICATIONS ^ Power Rating250 W / 1000 W Frequency Range60 Hz - 16 kHz (-10 dB) Dimensions (H x W x D)572 mm x 394 mm x 318 mm (22.5 in x 15.5 in x 12.5 in) Frequency Response70 Hz - 12 kHz (±3 dB) Nominal Impedance8 ohms Sensitivity99 dB SPL (1w/1m) Recommended Amplifier Power250 W to 500 W into 8 ohms Maximum SPL129 dB Nominal Dispersion90º x 50º Crossover Frequency1.8 kHz Weight19.5 kg (43 lb) High Frequency DriverJBL 2412 1 in exit compression driver mounted on Progressive Transition™ Waveguide Low Frequency DriverJBL M112-8 Input ConnectorsNeutrik® Speakon® NL-4 (x1); .25 in TS phone jack (x1); parallel View details Winning BidN/A Lot #113 JBL JRX112M Monitor- JBL 12 in low frequency driver with a 64 mm (2.5 in) diameter edgewound ribbon voice coil which provides more cross-sectional wire area in the voice coil gap than round wire designs, for greater efficiency and power handling. Ferro-fluid cooled compression driver with titanium diaphragm improves high frequency performance as well as system reliability. The advanced network topology crossover design shapes frequency response and delivers "coherent summation" in the crossover region. High-voltage capacitors and inductors with massive cores and heavy gauge wire enable the crossover network to handle high power without saturating. Progressive Transition™ high frequency waveguide provides superior coverage control, reduced distortion, and smoother frequency response. The rugged, acoustically superior enclosure is constructed from 19 mm (.75 in) MDF (Medium Density Fiberboard) using advanced adhesives and mechanical fastener technology for extreme durability and improved low-frequency performance. SonicGuard™ protects the highfrequency driver from excess power without interrupting the performance. Non-resonant, all-steel handles are used. Attractive 18-gauge hexagon perforated, steel grille protects components from damage. Dual-angle pole-mount socket allows the speaker to tilt 10°for more uniform audience coverage. SPECIFICATIONS ^ Power Rating250 W / 1000 W Frequency Range60 Hz - 16 kHz (-10 dB) Dimensions (H x W x D)572 mm x 394 mm x 318 mm (22.5 in x 15.5 in x 12.5 in) Frequency Response70 Hz - 12 kHz (±3 dB) Nominal Impedance8 ohms Sensitivity99 dB SPL (1w/1m) Recommended Amplifier Power250 W to 500 W into 8 ohms Maximum SPL129 dB Nominal Dispersion90º x 50º Crossover Frequency1.8 kHz Weight19.5 kg (43 lb) High Frequency DriverJBL 2412 1 in exit compression driver mounted on Progressive Transition™ Waveguide Low Frequency DriverJBL M112-8 Input ConnectorsNeutrik® Speakon® NL-4 (x1); .25 in TS phone jack (x1); parallel View details Winning BidN/A Lot #114 Yamaha SW218V Subwoofer Cabinet (JBL Speakers)- 2 - 18" woofers 30Hz-2kHz frequency response (-10dB) 1,220W program handling/2,400W peak Sensitivity: 98dB 48"W x 23"H x 26"D 132 lbs. View details Winning BidN/A Lot #115 Yamaha SW218V Subwoofer Cabinet (JBL Speakers)- 2 - 18" woofers 30Hz-2kHz frequency response (-10dB) 1,220W program handling/2,400W peak Sensitivity: 98dB 48"W x 23"H x 26"D 132 lbs. View details Winning BidN/A Lot #116 Yamaha SW218V Subwoofer Cabinet- 2 - 18" woofers 30Hz-2kHz frequency response (-10dB) 1,220W program handling/2,400W peak Sensitivity: 98dB 48"W x 23"H x 26"D 132 lbs. View details Winning BidN/A Lot #117 Yamaha SW218V Subwoofer Cabinet- 2 - 18" woofers 30Hz-2kHz frequency response (-10dB) 1,220W program handling/2,400W peak Sensitivity: 98dB 48"W x 23"H x 26"D 132 lbs. View details Winning BidN/A Lot #118 Furman M-8LX Power Conditioner (with lights)- Maximum Output Current: 15 ampsLine Cord: 6 ft., captive, 14 AWG, with 3-conductor Edison plugLamps: Two 120V incandescent bulbs, 4 watts eachOperating Voltage: 120VAC 60HzSpike Protection Mode: Line to neutralEnergy Dissipation: 170 joulesPeak Impulse Current: 12,000 ampsMaximum Continuous Opterating Voltage: 130 VAC RMSLet Through Voltage (@ 125 amps, 8/20uS waveform) 400 voltsNoise Attenuation: Transverse mode: Greater than 26dB, 200Khz to 10 MhzDimensions: 1.75" H x 19" W x 7.5" DWeight: 5.5 lbs. View details Winning BidN/A Lot #119 Ashly XR 1001 Crossover- The XR-1001 Crossover is based upon a powerful state-variable filter circuit guaranteeing that two adjacent frequency band outputs always remain in phase. It also includes a 200:1 tuning range, individual output mute switches, and both TRS and XLR connectors. Like other Ashly products, your crossover features low noise and distortion, active balanced inputs, a peak level indicator, a precision regulated power supply, protection against abnormal input or output conditions, and rugged mechanical construction. Conservative design and an unusually thorough procedure for quality control have earned Ashly a reputation for dependability in the recording, sound reinforcement, and broadcast fields. View details Winning BidN/A Lot #120 Crest CPQ-1131 Equalizer- The single-rack-space 31-band mono switchable 12 dB or 6 dB boost/cut range, plus a 40 Hz/24 dB low cut filter; and +/-12 dB gain control. 1/4" and XLR balanced/unbalanced I/O; constant Q filters; output level LEDs and bypass switch with status LED. CPQ-1131 Switchable 12 dB or 6 dB boost/cut range = Switchable 40 Hz/24 dB low cut filter Constant Q filters +/-12 dB gain control 1/4" and XLR balanced/unbalanced I/O Output level LEDs Bypass switch with status LED Single rack space unit U.S. MSRP TBA View details Winning BidN/A Lot #121 Behringer Ultragraph PRO FBQ1502HD- Professional 15-band stereo graphic equalizer for live and studio applications Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer Ultra-low noise 4580 operational amplifiers for highest signal integrity Dedicated mono subwoofer output with adjustable crossover frequency Additional low-cut filter removes unwanted frequencies, e.g. floor rumble View details Winning BidN/A Lot #122 Behringer Ultragraph PRO FBQ1502HD- Professional 15-band stereo graphic equalizer for live and studio applications Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer Ultra-low noise 4580 operational amplifiers for highest signal integrity Dedicated mono subwoofer output with adjustable crossover frequency Additional low-cut filter removes unwanted frequencies, e.g. floor rumble View details Winning BidN/A Lot #123 QSC PLX 3402 Power Amp- Powerful and Lightweight, the PLX Series features PowerWave technology for bigger bass, cleaner highs, and greater reliability... and it weighs ONLY 21lbs! • 1700 Watts per Channel at 2 ohms • 1100 Watts per Channel at 4 ohms • 700 Watts per Channel at 8 ohms • 3400 Watts Bridged Mono @ 4 ohms • 2200 Watts Bridged Mono @ 8 ohms FEATURES: • Exclusive PowerWave power supply for superior bass and lighter weight • Ultra-low distortion (0.03% THD at 8 ohms) and studio-quality noise floor (-107 dB) • LED indicators include bridge mono and parallel input modes • Compact 2 RU, 21 lbs. and 13inch deep chassis fits into any rack • Class H output reduces AC power draw and heat by 40% (2402, 3002, and 3402) • Selectable clip limiters and subsonic filters reduce distortion and protect speakers • Variable-speed fan for low noise and solid 2 ohm performance • Both 1/4 inch TRS and XLR inputs, Speakon and shock-proof binding post outputs • 3-year warranty plus optional 3-year extension available • Distortion (SMPTE-IM) Less than 0.01% • Distortion (typical): 20 Hz-20 KHz: 10 dB below rated power, 1.0 kHz and below: full rated power Less than 0.01% THD • Frequency Response 20 Hz-20 kHz, 0.2 dB/8 Hz-50 kHz, 0, -3 dB • Damping Factor greater than 500 • Input Impedance 6 K ohms unbalanced, 12 K ohms balanced • Input Clipping 10 Vrms (22dB) • Cooling Variable-speed fan, rear-to-front air flow • Connectors (each channel) Input: 3-pin XLR and 1/4 inch TRS balanced • Output: Neutrik Speakon and touch-proof binding posts • Amplifier Protection Full short circuit, open circuit, thermal, ultrasonic, and protection. • Stable into reactive or mismatched loads. • Load Protection On/off muting, DC-fault power supply shutdown View details Winning BidN/A Lot #124 QSC PL340 Powerlight 3 Power Amp- QSC PL340 specs Power Rating Stereo Mode: 8Ω EIA 1 kHz 1% THD - 800W 4Ω EIA 1 kHz 1% THD - 1250W 2Ω EIA 1 kHz 1% THD - 2000W Bridged Mono: 8Ω EIA 1 kHz 1% THD - 2600W 4Ω EIA 1 kHz 1% THD - 4000W Damping Factor Not Specified By Manufacturer Input Sensitivity26dB Setting - 3.92V 32dB Setting - 1.96V Input Impedance> 10kΩ balanced, or unbalanced Gain36.4dB Frequency Response20Hz to 20kHz, +/- 0.2dB Signal-to-Noise Ratio-105dB Total Harmonic Distortion (THD)0.02% @ 2Ω 0.005-0.01% @ 4Ω 0.002-0.01% @ 8Ω Input ConnectionsInput: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel) DataPort: HD-15, input signal in parallel with XLR input connectors Output ConnectorsOutput: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts Controls Front PanelAC Power Switch Gain Controls, 21 detents, 1 dB steps (each channel) Controls (Rear)Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange) Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow) High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange) Clip Limiter (each channel): Off, On (Yellow) IndicatorsClip Limiter (each channel): Off, On (Yellow) CoolingFlow-thru air path and solid aluminum heat sinks Power Consumption120V 50/60Hz - 12A 230V 50Hz - 7A Power Requirements Not Specified By Manufacturer Dimensions (WxHxD)19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm) Weight33.5 lbs (15.2kg) SpecialtiesParallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity View details Winning BidN/A Lot #125 8 output Speakon rack panel- Easy front mount design. View details Winning BidN/A Lot #126 Custom Built Top Enclosure (JBL Drivers-2" Throat / EV SM2151 15" Woofer)- Professional Built Enclosure. JBL 2446H Compression Driver (8ohm) EV SM 2151 15" Woofer (500watt-2000 peak) The model 2446H/J is a professional quality high-frequency compression driver that incorporates JBL's newlydeveloped Coherent Wave phasing plug as well as a pure titanium diaphragm with radial ribs and patented three-dimensional diamond pattern suspension. The Coherent Wave phasing plug assembly consists of four die-cast annular aperture structures of constant path length to provide m-phase combining of diaphragm output at the driver's exit. This optimized configuration allows coherent summation of acoustical power up to much higher frequencies than afforded by earlier designs. The diaphragm design includes JBL's exclusive three-dimensional diamond pattern surround1 which reduces membrane stresses in the diaphragm support structure and extends diaphragm life. The depth of the diamond pattern is closely controlled during the manufacturing process to provide predictable frequencies for the 2nd and 3rd normal resonance modes and for the basic suspension resonance mode. The diaphragm also incorporates a series of embossed radial reinforcing ribs that increase diaphragm stiffness. This diaphragm, when combined with the Coherent Wave phasing plug, increases the 2446H/J's output in the 5 kHz to 20 kHz range. Specifications: Throat Diameter: 49 mm (2 in) Nominal Impedance:2446H 8 ohms2446J 16 ohms Minimum Impedance: 6 ohms (H), 12 ohms (J) @ 5 kHz DC Resistance: 4.3 ohms (H), 8.5 ohms (J) +/- 10% @ 25C Power Capacity:100 W continuous program above 500 Hz150 W continuous program above 1 kHz Sensitivity:111 dB SPL, 1 W @ 1 m on-axis on horn118 dB SPL, 1 mW on plane-wave tube(3) Nominal Efficiency: 30% (500 Hz to 2.5 kHz) Frequency Range: 500 Hz to 20 kHz Recommended Crossover: 500 Hz or higher, 12 dB/octave minimum Diaphragm: 0.05 mm (0.002 in) pure titanium Voice Coil Diameter: 100 mm (4 in) Voice Coil Material: Edgewound aluminum ribbon Flux Density: 1.9 T (19,000 gauss) Bl Factor:12.7 (H) N/A18 (J) N/A Positive voltage to black terminal gives diaphragm motion toward the phasing plug Dimensions: 235 mm (9-1/4 in) diameter, 131 mm (5-3/16 in) depth Mounting: Four 1/4-20 threaded holes, 90 apart on 101.6 mm (4 in) diameter Net Weight: 13.8 kg (30-1/2 lb View details Winning BidN/A Lot #127 Custom Built Top Enclosure (JBL Drivers-2" Throat / EV SM2151 15" Woofer)- Professional Built Enclosure. JBL 2446H Compression Driver (8ohm) EV SM 2151 15" Woofer (500watt-2000 peak) The model 2446H/J is a professional quality high-frequency compression driver that incorporates JBL's newlydeveloped Coherent Wave phasing plug as well as a pure titanium diaphragm with radial ribs and patented three-dimensional diamond pattern suspension. The Coherent Wave phasing plug assembly consists of four die-cast annular aperture structures of constant path length to provide m-phase combining of diaphragm output at the driver's exit. This optimized configuration allows coherent summation of acoustical power up to much higher frequencies than afforded by earlier designs. The diaphragm design includes JBL's exclusive three-dimensional diamond pattern surround1 which reduces membrane stresses in the diaphragm support structure and extends diaphragm life. The depth of the diamond pattern is closely controlled during the manufacturing process to provide predictable frequencies for the 2nd and 3rd normal resonance modes and for the basic suspension resonance mode. The diaphragm also incorporates a series of embossed radial reinforcing ribs that increase diaphragm stiffness. This diaphragm, when combined with the Coherent Wave phasing plug, increases the 2446H/J's output in the 5 kHz to 20 kHz range. Specifications: Throat Diameter: 49 mm (2 in) Nominal Impedance:2446H 8 ohms2446J 16 ohms Minimum Impedance: 6 ohms (H), 12 ohms (J) @ 5 kHz DC Resistance: 4.3 ohms (H), 8.5 ohms (J) +/- 10% @ 25C Power Capacity:100 W continuous program above 500 Hz150 W continuous program above 1 kHz Sensitivity:111 dB SPL, 1 W @ 1 m on-axis on horn118 dB SPL, 1 mW on plane-wave tube(3) Nominal Efficiency: 30% (500 Hz to 2.5 kHz) Frequency Range: 500 Hz to 20 kHz Recommended Crossover: 500 Hz or higher, 12 dB/octave minimum Diaphragm: 0.05 mm (0.002 in) pure titanium Voice Coil Diameter: 100 mm (4 in) Voice Coil Material: Edgewound aluminum ribbon Flux Density: 1.9 T (19,000 gauss) Bl Factor:12.7 (H) N/A18 (J) N/A Positive voltage to black terminal gives diaphragm motion toward the phasing plug Dimensions: 235 mm (9-1/4 in) diameter, 131 mm (5-3/16 in) depth Mounting: Four 1/4-20 threaded holes, 90 apart on 101.6 mm (4 in) diameter Net Weight: 13.8 kg (30-1/2 lb View details Winning BidN/A Lot #128 Custom Built Top Enclosure (JBL Drivers-2" Throat / EV SM2151 15" Woofer)- Professional Built Enclosure. JBL 2446H Compression Driver (8ohm) EV SM 2151 15" Woofer (500watt-2000 peak) The model 2446H/J is a professional quality high-frequency compression driver that incorporates JBL's newlydeveloped Coherent Wave phasing plug as well as a pure titanium diaphragm with radial ribs and patented three-dimensional diamond pattern suspension. The Coherent Wave phasing plug assembly consists of four die-cast annular aperture structures of constant path length to provide m-phase combining of diaphragm output at the driver's exit. This optimized configuration allows coherent summation of acoustical power up to much higher frequencies than afforded by earlier designs. The diaphragm design includes JBL's exclusive three-dimensional diamond pattern surround1 which reduces membrane stresses in the diaphragm support structure and extends diaphragm life. The depth of the diamond pattern is closely controlled during the manufacturing process to provide predictable frequencies for the 2nd and 3rd normal resonance modes and for the basic suspension resonance mode. The diaphragm also incorporates a series of embossed radial reinforcing ribs that increase diaphragm stiffness. This diaphragm, when combined with the Coherent Wave phasing plug, increases the 2446H/J's output in the 5 kHz to 20 kHz range. Specifications: Throat Diameter: 49 mm (2 in) Nominal Impedance:2446H 8 ohms2446J 16 ohms Minimum Impedance: 6 ohms (H), 12 ohms (J) @ 5 kHz DC Resistance: 4.3 ohms (H), 8.5 ohms (J) +/- 10% @ 25C Power Capacity:100 W continuous program above 500 Hz150 W continuous program above 1 kHz Sensitivity:111 dB SPL, 1 W @ 1 m on-axis on horn118 dB SPL, 1 mW on plane-wave tube(3) Nominal Efficiency: 30% (500 Hz to 2.5 kHz) Frequency Range: 500 Hz to 20 kHz Recommended Crossover: 500 Hz or higher, 12 dB/octave minimum Diaphragm: 0.05 mm (0.002 in) pure titanium Voice Coil Diameter: 100 mm (4 in) Voice Coil Material: Edgewound aluminum ribbon Flux Density: 1.9 T (19,000 gauss) Bl Factor:12.7 (H) N/A18 (J) N/A Positive voltage to black terminal gives diaphragm motion toward the phasing plug Dimensions: 235 mm (9-1/4 in) diameter, 131 mm (5-3/16 in) depth Mounting: Four 1/4-20 threaded holes, 90 apart on 101.6 mm (4 in) diameter Net Weight: 13.8 kg (30-1/2 lb View details Winning BidN/A Lot #129 Custom Built Top Enclosure (JBL Drivers-2" Throat / EV SM2151 15" Woofer)- Professional Built Enclosure. JBL 2446H Compression Driver (8ohm) EV SM 2151 15" Woofer (500watt-2000 peak) The model 2446H/J is a professional quality high-frequency compression driver that incorporates JBL's newlydeveloped Coherent Wave phasing plug as well as a pure titanium diaphragm with radial ribs and patented three-dimensional diamond pattern suspension. The Coherent Wave phasing plug assembly consists of four die-cast annular aperture structures of constant path length to provide m-phase combining of diaphragm output at the driver's exit. This optimized configuration allows coherent summation of acoustical power up to much higher frequencies than afforded by earlier designs. The diaphragm design includes JBL's exclusive three-dimensional diamond pattern surround1 which reduces membrane stresses in the diaphragm support structure and extends diaphragm life. The depth of the diamond pattern is closely controlled during the manufacturing process to provide predictable frequencies for the 2nd and 3rd normal resonance modes and for the basic suspension resonance mode. The diaphragm also incorporates a series of embossed radial reinforcing ribs that increase diaphragm stiffness. This diaphragm, when combined with the Coherent Wave phasing plug, increases the 2446H/J's output in the 5 kHz to 20 kHz range. Specifications: Throat Diameter: 49 mm (2 in) Nominal Impedance:2446H 8 ohms2446J 16 ohms Minimum Impedance: 6 ohms (H), 12 ohms (J) @ 5 kHz DC Resistance: 4.3 ohms (H), 8.5 ohms (J) +/- 10% @ 25C Power Capacity:100 W continuous program above 500 Hz150 W continuous program above 1 kHz Sensitivity:111 dB SPL, 1 W @ 1 m on-axis on horn118 dB SPL, 1 mW on plane-wave tube(3) Nominal Efficiency: 30% (500 Hz to 2.5 kHz) Frequency Range: 500 Hz to 20 kHz Recommended Crossover: 500 Hz or higher, 12 dB/octave minimum Diaphragm: 0.05 mm (0.002 in) pure titanium Voice Coil Diameter: 100 mm (4 in) Voice Coil Material: Edgewound aluminum ribbon Flux Density: 1.9 T (19,000 gauss) Bl Factor:12.7 (H) N/A18 (J) N/A Positive voltage to black terminal gives diaphragm motion toward the phasing plug Dimensions: 235 mm (9-1/4 in) diameter, 131 mm (5-3/16 in) depth Mounting: Four 1/4-20 threaded holes, 90 apart on 101.6 mm (4 in) diameter Net Weight: 13.8 kg (30-1/2 lb View details Winning BidN/A Lot #130 16 Space Rolling Road Case- ATA Style Construction Great Shape View details Winning BidN/A Lot #131 JBL JRX112M Monitor- JBL 12 in low frequency driver with a 64 mm (2.5 in) diameter edgewound ribbon voice coil which provides more cross-sectional wire area in the voice coil gap than round wire designs, for greater efficiency and power handling. Ferro-fluid cooled compression driver with titanium diaphragm improves high frequency performance as well as system reliability. The advanced network topology crossover design shapes frequency response and delivers "coherent summation" in the crossover region. High-voltage capacitors and inductors with massive cores and heavy gauge wire enable the crossover network to handle high power without saturating. Progressive Transition™ high frequency waveguide provides superior coverage control, reduced distortion, and smoother frequency response. The rugged, acoustically superior enclosure is constructed from 19 mm (.75 in) MDF (Medium Density Fiberboard) using advanced adhesives and mechanical fastener technology for extreme durability and improved low-frequency performance. SonicGuard™ protects the highfrequency driver from excess power without interrupting the performance. Non-resonant, all-steel handles are used. Attractive 18-gauge hexagon perforated, steel grille protects components from damage. Dual-angle pole-mount socket allows the speaker to tilt 10°for more uniform audience coverage. SPECIFICATIONS ^ Power Rating250 W / 1000 W Frequency Range60 Hz - 16 kHz (-10 dB) Dimensions (H x W x D)572 mm x 394 mm x 318 mm (22.5 in x 15.5 in x 12.5 in) Frequency Response70 Hz - 12 kHz (±3 dB) Nominal Impedance8 ohms Sensitivity99 dB SPL (1w/1m) Recommended Amplifier Power250 W to 500 W into 8 ohms Maximum SPL129 dB Nominal Dispersion90º x 50º Crossover Frequency1.8 kHz Weight19.5 kg (43 lb) High Frequency DriverJBL 2412 1 in exit compression driver mounted on Progressive Transition™ Waveguide Low Frequency DriverJBL M112-8 Input ConnectorsNeutrik® Speakon® NL-4 (x1); .25 in TS phone jack (x1); parallel View details Winning BidN/A Lot #132 JBL JRX112M Monitor- JBL 12 in low frequency driver with a 64 mm (2.5 in) diameter edgewound ribbon voice coil which provides more cross-sectional wire area in the voice coil gap than round wire designs, for greater efficiency and power handling. Ferro-fluid cooled compression driver with titanium diaphragm improves high frequency performance as well as system reliability. The advanced network topology crossover design shapes frequency response and delivers "coherent summation" in the crossover region. High-voltage capacitors and inductors with massive cores and heavy gauge wire enable the crossover network to handle high power without saturating. Progressive Transition™ high frequency waveguide provides superior coverage control, reduced distortion, and smoother frequency response. The rugged, acoustically superior enclosure is constructed from 19 mm (.75 in) MDF (Medium Density Fiberboard) using advanced adhesives and mechanical fastener technology for extreme durability and improved low-frequency performance. SonicGuard™ protects the highfrequency driver from excess power without interrupting the performance. Non-resonant, all-steel handles are used. Attractive 18-gauge hexagon perforated, steel grille protects components from damage. Dual-angle pole-mount socket allows the speaker to tilt 10°for more uniform audience coverage. SPECIFICATIONS ^ Power Rating250 W / 1000 W Frequency Range60 Hz - 16 kHz (-10 dB) Dimensions (H x W x D)572 mm x 394 mm x 318 mm (22.5 in x 15.5 in x 12.5 in) Frequency Response70 Hz - 12 kHz (±3 dB) Nominal Impedance8 ohms Sensitivity99 dB SPL (1w/1m) Recommended Amplifier Power250 W to 500 W into 8 ohms Maximum SPL129 dB Nominal Dispersion90º x 50º Crossover Frequency1.8 kHz Weight19.5 kg (43 lb) High Frequency DriverJBL 2412 1 in exit compression driver mounted on Progressive Transition™ Waveguide Low Frequency DriverJBL M112-8 Input ConnectorsNeutrik® Speakon® NL-4 (x1); .25 in TS phone jack (x1); parallel View details Winning BidN/A Lot #133 Yamaha O1V Digital Mixer- Yamaha 01V Specifications: Digital IOs: Stereo i/o on S/PDIF coax Analog IOs: 12 mono (XLR/bal. jack) 2 stereo (bal. jack) 4 omni out (bal. jack) mix out (2x male XLR) Midi IOs: in/out/thru Other IOs: 2-track i/o (RCA phono), monitor out (bal. jack), headphones (1/4 Busses/Subgroups: 4 Aux sends: 4 aux sends Maximum Resolution:44.1kHz sampling rate, 32 bit processing (internal EQ: 4 band fully parametric on inputs 1-16, fx returns, aux sends and stereo out Dynamics: 22 processors (compressor, gate, expander, ducker, compander) FX: 2 separate processors Software supported: - Upgrades/Extras: 8 digi i/o as AES/EBU, ADAT optical, TDIF, 4 extra outs (XLR) or 8 extra analogue ins (balanced jack) View details Winning BidN/A Lot #134 BBE Sonic Maximizer 882i- Applications Broadcasting DJ Sound Reinforcement Mastering Musical Instruments Tape Duplication Recording Professional Sound Reinforcement Features include A full-function Sonic Maximizer, +23dB of output headroom, balanced or unbalanced I/O, 115dB signal to noise ratio and Hard-wire bypass. +4dBu balanced line (1/4" tip-ring-sleeve and XLR inputs and outputs) +23dBu headroom Active balanced outputs Hardwire bypass Bypass switch for comparison of processed to unprocessed signal Specifications Frequency Response, Process Mode: Program controlled Bypass Mode: 10Hz to 50kHz, +/- 0.5dBu, 0dBu input Signal to Noise Ratio: 115dB Process IN THD, Process mode: less than 0.025% 20-20kHz Bypass mode: less than 0.002% 20-20kHz Maximum Output: +23dBu (may vary due to control settings) Input Impedance: 14.7K Ohms, balanced 1/4" stereo phone jack or XLR jack. Pin #2 is the hot or "+" signal. Output Impedance: 600 Ohms, balanced 1/4" stereo phone jack or XLR jack. Pin #2 is the hot or "+" signal. Sensitivity: -45dBu for maximum process Maximum Process: +12dBu boost at 5kHz, 0dBu input Lo Contour: +12dBu adjustment at 50Hz, 0dBu input Designed and Engineered in USA Made in China View details Winning BidN/A Lot #135 (Quantity - 2) JBL 2380A Horns- Throat Diameter 2" / 49mm Dispersion90°H x 40°V ThrowShort Average Frequency Range1kHz - 16kHz Usable Low Frequency Limit 400 Hz Min. Recommended Crossover500 Hz @ 18dB octave Directivity Factor (Q)10.7 Directivity Index (DI)10.3 Axial Pressure Sensitivity112dB Construction MaterialMolded Structural Foam Net Weight 2.2 kg. / 6 lbs. MOUNTING INFORMATION Overall Height 11" / 279 mm Overall Width 17.5" / 445mm Overall Length9.28" / 236mm Baffle Cutout Height9.375" / 238mm Baffle Cutout Width15.875" / 403mm View details Winning BidN/A Items per page 102550100 Previous|1|Next Previous 1 Next Previous 1 Next